No edit summary |
No edit summary |
||
| Line 13: | Line 13: | ||
# Note the MAC address to look for it in the router management console to ensure the machine has successfully connected to the network. | # Note the MAC address to look for it in the router management console to ensure the machine has successfully connected to the network. | ||
{| | {| | ||
|[[File:Fanuc embedded network settings.webp|none|thumb|Embedded network settings]] | |[[File:Fanuc embedded network settings.webp|none|thumb|Embedded network settings]] | ||
|[[File:FANUC PCMCIA network settings.webp|none|thumb|PCMCIA network settings]] | |[[File:FANUC PCMCIA network settings.webp|none|thumb|PCMCIA network settings]] | ||
|- | |||
| colspan="2" |This machine is connected to a network via the embedded Ethernet interface and does not have a PCMCIA Ethernet interface installed. | |||
|} | |} | ||
| Line 22: | Line 23: | ||
# Make sure a TCP port number is specified. FOCAS over UDP is not supported at this time. This value is usually 8193 by default, but can be set to any port not in use by other software on the control. This number must be entered into OnTakt. | # Make sure a TCP port number is specified. FOCAS over UDP is not supported at this time. This value is usually 8193 by default, but can be set to any port not in use by other software on the control. This number must be entered into OnTakt. | ||
{| | {| | ||
|- | |- | ||
|[[File:FANUC FOCAS2 Embedded settings.webp|none|thumb|Embedded FOCAS2 settings]] | |[[File:FANUC FOCAS2 Embedded settings.webp|none|thumb|Embedded FOCAS2 settings]] | ||
|[[File:FANUC FOCAS2 PCMCIA settings.webp|none|thumb|PCMCIA FOCAS2 settings]] | |[[File:FANUC FOCAS2 PCMCIA settings.webp|none|thumb|PCMCIA FOCAS2 settings]] | ||
|- | |||
| colspan="2" |This machine has FOCAS enabled on port 8193 of the embedded Ethernet interface but does not have it enabled on the PCMCIA Ethernet interface. | |||
|} | |} | ||
Revision as of 13:39, 14 February 2023
FANUC FOCAS allows external systems such as OnTakt to communicate with a FANUC control.
Configuration
These instructions are for FANUC 30i/31i/32i controls.
- Press the SYSTEM control key.
- Scroll through the list of soft keys until "EMBED PORT" and "PCMCIA LAN" are listed.
- Select the Ethernet adapter that is connected to the network. This is usually "EMBED PORT", but may be "PCMCIA LAN" in some cases. The embedded port is located inside the HMI or machine cabinet, and the PCMCIA Ethernet would in a card slot inside the control or machine cabinet if it is present. Newer controls show an "AVAILABLE DEVICE" item inside both adapter configuration panels that indicate which adapter is connected, as shown in the screenshots below.
Network configuration
- Press the COMMON soft key.
- Make sure the IP address, subnet mask, and router IP address are correct for the network the machine is on.
- Note the MAC address to look for it in the router management console to ensure the machine has successfully connected to the network.
| This machine is connected to a network via the embedded Ethernet interface and does not have a PCMCIA Ethernet interface installed. | |
FOCAS2 configuration
- Press the FOCAS2 soft key.
- Make sure a TCP port number is specified. FOCAS over UDP is not supported at this time. This value is usually 8193 by default, but can be set to any port not in use by other software on the control. This number must be entered into OnTakt.
| This machine has FOCAS enabled on port 8193 of the embedded Ethernet interface but does not have it enabled on the PCMCIA Ethernet interface. | |
OnTakt
When setting up a machine in OnTakt using FANUC FOCAS, enter the NC URL in the format tcp://<ip>:<port>. For example, if the machine IP is 10.0.0.5 and the port is 8193, enter tcp://10.0.0.5:8193. FOCAS over UDP is not supported at this time.